Logo Banner

Home
R.O. Theory
Our Products
Related Products
Testimonials 
St Roch II Story
Links
Contact Us



Kubota 12V Genset & Modular WaterMaker Kit

The Aquagen can make fresh soft water, power, run your dive compressor or hydraulic system, heat your water, and charge your refrigeration all at the same time, "we custom build these systems"

The popular AquaGen 150 is a compact, low fuel consuming powerhouse, capable of producing up to 150 amps and from 8 up to 62 GPH of fresh water. It will also work well from river, lake, or sea-water. A refrigeration compressor may be added, and/or a hydraulic pump to power additional accessories such as a dive compressor, 150 GPM bilge pump, bow thruster or windlass.

The generator set and watermaker high pressure pump are assembled as a compact unit with membranes mounted under the genset or elsewhere in the vessel. The watermaker's control panel can be mounted topside. Expansion capability is built into all sizes. Fan cooled radiator with backup alternator and/or marine heat exchanger with wet exhaust combinations are available on all units whether for sea or land use. All electrical components are mounted above all the water components. Note that our Kubota engines retain the original Kubota two year factory warranty.
          Note: It is the purchaser's responsibility to supply a safety belt/pulley guard for this kit.

NEW! Compact Kubota 12 VOLT diesel Genset only. Click here for more information.

 
UPGRADE MODEL WITH REFRIGERATION COMPRESSOR (UPPER RIGHT) AND R.O. MEMBRANES MOUNTED UNDERNEATH,

AquaMarine can supply a full range of Kubota engines. Click here for more information.

KIT CONTENTS

  • Kubota diesel engine with vibration damping counter balances.
  • Stainless steel mounting brackets, and shock absorbing rubber feet with double 3/8" stud mounting.
  • Heavy-duty spring-loaded spike absorbing automatic belt tensioning idler arm.
  • K6 Polly groove pulleys, & belt for maximum efficiency. Vented heavy-duty 12 volt electric clutch for remote operation.
  • Standard high-pressure pump with aluminum/nickel bronze (or optional stainless steel upgrade) pump head with lifetime limited warranty to original non-commercial marine purchaser.
  • High temp large frame 200 amp 12-volt alternator.
  • 1000psi certified filament wound fiberglass RO membrane housing(s) with Super Austenitic S/S end plugs and quadruple o rings, mounting bracket, and a lifetime limited warranty to the original non-commercial marine purchaser.
  • Thin film, spiral wound 1000 psi, 50,000 ppm high rejection (99.7%), heavy duty RO membrane(s) including one pound of cruising membrane preservative.
  • 316 Stainless steel remote control panel including flow meters, hour meter, stainless pressure gauge, stainless manual regulator valve, three way selector valve, overload circuit breaker, safety stainless high pressure switch, and indicator light, and laser engraving.
  • Prefilters (5 and 20 micron) with clear housings, stainless mounting brackets, safety low pressure switch and service wrench.
  • 20' nylon lined high pressure hose with reusable fittings.
  • 10' heavy duty white 3/4" reinforced feed water hose and fittings.
  • 15' heavy duty red polyethylene brine water discharge tubing and fittings.
  • 15' FDA approved blue polyethylene product water tubing and fittings.
  • 3/8" inline check valve for product water tubing between TDS valve and storage tank.
  • 12-volt self-adjusting boost pump with magnetic shaft coupling.
  • Miscellaneous fittings, screws, hose mounts, etc. to run up to 20 feet from genset to control panel.
  • Set of installation diagrams and instructions.
  • Toll Free assistance line for installs or technical support.


          SIZE OPTIONS              
SIZE * H.P. SIZE * H.P.
 12 GPH 6 Hp 40 GPH 6 Hp
24 GPH 6 Hp 62 GPH 6 Hp
32 GPH 6 Hp 113 GPH 13.5 Hp   
  
* The above flow rates are based on a TDS of 36,000 ppm at 78 degrees F. Flow rates are +/-5%

MISCELLANEOUS OPTIONS

                                                           

Refrigeration compressor 150 GPM emergency bilge pump
8" Diameter
Hydraulic pump
D 4 1/4"
W 3 5/8"
H 3 3/8"
Shaft 9/16" dia.

      Custom Hydraulic/R.O. Attachments

 

ADDITIONAL MEMBRANE MODULE(S) FOR HIGHER PRODUCTION
HIGH PRESSURE WASH DOWN KIT (SALT & FRESH WATER) WITH 25FT. OF 2000 PSI NON MARKING DECK HOSE
12 VOLT D.C. OR 120 VOLT A.C. UV STERILIZER UNIT WITH S/S LINER (FOR SHIP'S TANK)
SPARE 5 MICRON / 20 MICRON PRE-FILTER ELEMENTS
SPARE 5 MICRON / 20 MICRON PRE-FILTER ELEMENTS PER CASE OF (30) $60 SAVINGS PER CASE
12 VOLT 7" MAGNETIC CLUTCH SINGLE OR DOUBLE SHEAVE (INCLUDED IN ABOVE PRICES)
UP-GRADE S/S PANEL FROM 32 GPH TO 62 GPH CAPACITY
PORTABLE HAND HELD SALINITY MONITOR
ADDITIONAL MEMBRANE MODULE(S) FOR HIGHER PRODUCTION
HYDRAULIC BELL HOUSING (TO POWER THE R.O. HIGH PRESSURE PUMP WITH A HYDRAULIC MOTOR)
316 STAINLESS STEEL PUMP HEAD (62 GPH MAX.)
REFRIGERATION COMPRESSORS, HYDRAULIC PUMPS, 150 GPM BILGE PUMPS AND DIVE COMPRESSORS AVAILABLE
FULL HYDRAULIC SYSTEM INCLUDING HYDRAULIC PUMP, HEAT EXCHANGER/HYDRAULIC RESERVOIR, HYDRAULIC FLOW CONTROL VALVE, HOSES AND FITTINGS, AND REQUIRED PUMPS AND ACCESSORIES

Kubota Right Side

Aquagen 150 Set-up, Front  view
28"L x 13.5"W x 15.75"H
If membranes are mounted below add 2.5" to height.


8-32 GPH Control Panel
316L Stainless Steel
Laser Engraved

11.75" x 6.75"

 Panels also come in a black plastic cover.


62 GPH Control Panel
316L Stainless Steel
Laser Engraved

11.75" x 6.75"

Kubota Rear Side

Aquagen 150 Set-up, Front & Rear View
28"L x 13.5"W x 15.75"H
If membranes are mounted below add 2.5" to height.

Hydraulic unit only. All of these systems come with electric and hand crank starting.





Website and all contents copyright, © 1996-2016, by AquaMarine, Inc. All Rights Reserved
Please review legal terms and conditions of use by clicking here.

PO Box 55, Deer Harbor, WA 98243-0055 USA
Ph: 1-800-376-3091 or (360) 376-3091 fax: (360) 376-3243
All rights reserved.
 

Email us: aqua2133@me.com

 


Most products are sold duty free to Canadian residents.